The Stage Series A-Pillar Pod Kit for the 2019–2023 Polaris RZR XP is the ultimate solution to add versatile lighting to your off-road vehicle. Featuring durable brackets and high-performance LED pods, this kit provides a significant increase in light output while enhancing your vehicle's appearance. Designed for easy installation with factory mounting points, the kit requires no drilling or cutting and is backed by an 8-year warranty. Watch our installation video or continue reading below for detailed instructions!
Table of Contents
Installation Video
Tools Required
- 15mm Socket
- 10mm Socket and Wrench
- T25 Torx Driver
- 5/32" Allen Wrench
- 13mm Wrench
- Zip Ties
- Plastic Trim Removal Tools
Installation Instructions
Step 1 - Remove the Factory Bolts
Using a 15mm socket, remove the bottom bolt from the A-pillar. Slide the included spacer onto the bolt and loosely re-secure it to the vehicle. Next, remove the top bolt and position the driver-side A-pillar bracket over the bottom bolt.
Step 2 - Install the A-Pillar Brackets
Place a spacer between the A-pillar and the bracket, then thread the top bolt through the bracket and spacer. Adjust the bracket with a level and tighten both bolts securely. Repeat this process on the passenger side.
Step 3 - Connect the Wiring Harness
If connecting to a bus bar, use a 10mm socket to loosen the positive and negative terminals. Add the leads from the harness and mount the relay using the T25 screw on the bus bar. For battery connections, remove the driver’s seat to access the battery. Loosen the terminals with a 10mm wrench, attach the harness leads, and route the DT connectors to each pod, keeping them away from hot or moving parts.
Install Rectangular Rocker Switch (Optional)
If desired, the included wiring harness can be controlled using the Diode Dynamics Rectangular Rocker Switch. To install the switch, disconnect the factory harness switch by unplugging it from the white connector on the switch lead. Connect the rectangular rocker switch directly to this connector.
Route the switch wiring to your preferred mounting location and remove the factory switch blank from the dashboard or switch panel. Insert the rocker switch into the opening until it is fully seated.
The rocker switch features integrated backlighting and must be grounded for illumination. Attach the black wire with the ring terminal to a suitable chassis ground point on the vehicle.
Step 4 - Assemble the LED Pods
Drop the supplied nuts into the slots on the sides of the pods. With the nylon ring facing inward, slide the universal bracket over the back of the pod and secure it using the 5/32" Allen screws and washers. Repeat for the other pod.
For SS5 configurations: Refer to the Diode Dynamics SS5 LED Pods Installation Guide for additional SS5 mounting, wiring, and backlight information.
Step 5 - Mount the Pods
Plug in the DT connector to each pod. Place the pods on the A-pillar brackets and secure them using the included carriage bolts, washers, lock washers, and nuts. Tighten the assembly using a 13mm wrench. Test the pods for functionality and make final aiming adjustments as needed.
Step 6 - Finalize the Installation
Secure any loose wiring with zip ties and ensure the pods are properly aimed. Tighten all hardware using a 5/32" Allen wrench and a 13mm wrench. The installation is now complete. Enjoy your new Stage Series A-Pillar Pod Kit!
SS5 Backlight Color Programming
The following programming instructions apply only to A-pillar pod kits equipped with SS5 LED Pods. SS5 LED Pods offer multiple backlight color options, including White (default), Red, Blue, Green, Purple, Yellow, Amber, and Teal.
- Start with all backlight power OFF.
- Cycle backlight power ON and OFF three times within three seconds, spacing each ON press about one second apart.
- After the third cycle, the backlight will enter programming mode.
- Continue cycling power at the same steady pace to scroll through the available colors.
- When the desired color is displayed, leave the backlight ON.
- After five seconds, the color will save automatically and exit programming mode.
- Turn power OFF.
The selected color will appear any time backlight power is applied during normal operation.
SS5 Backlight Color Reset
The following reset procedure applies only to A-pillar pod kits equipped with SS5 LED Pods. If multiple SS5 LED Pods are connected to the same backlight circuit and the colors become unsynchronized, perform the following reset procedure.
- Enter backlight programming mode by cycling power ON and OFF three times, using the same one-second timing.
- Continue cycling power through all available colors twice. This requires at least sixteen total power cycles.
- After all colors have displayed twice, all connected lights will reset to White.
- Leave the backlight ON for five seconds to save the reset.
- Program the desired backlight color as outlined above if needed.
Questions About the Installation?
If you have any questions about installing the Stage Series A-Pillar Pod Kit for the 2019–2023 Polaris RZR XP, visit our support page or contact your local dealer.
Where Can I Buy the Stage Series A-Pillar Pod Kit for the 2019–2023 Polaris RZR XP?
If you're ready to upgrade your 2019–2023 Polaris RZR XP with the Stage Series A-Pillar Pod Kit, click here or use our Dealer Locator to find a dealer near you.
Looking to take your RZR XP's lighting to the next level? Check out all of our Polaris RZR XP LED Lighting Upgrades!
Want to know more about Diode Dynamics products? Visit DiodeDynamics.com and subscribe to our newsletter for new product releases and more!
This Installation Guide is for the following SKUs: DD8080, DD8081, DD8082, DD8083, DD8084, DD8085, DD8086, DD8087, DD8079P
Share This Post