Angel Eye Kit (for Projector Housing) for 2008-2014 Dodge Challenger

You could receive 20 Diode Points for writing a review for this product.

Availability: In stock

Ships today if ordered in the next 12 hours and 49 minutes!

DIY angel eye kit for your vehicle!
  • Multicolor SMD LED

MULTICOLOR ONLY: Required for Installation

OPTIONAL: This kit includes a LED toggle switch and wiring used to turn AEs on and off.

* Required Fields

Add to Wishlist

Angel Eye Kit (for Projector Housing) for 2008-2014 Dodge Challenger

More Views

  • Angel Eye kit
Customer Images
Earn $1.00 store credit! Upload a picture of this product installed for 20 Diode Points. (2MB limit)


Angel Eyes can be installed on any vehicle as an accent for your headlights. They can be found on BMWs and are a nice modification for any vehicle. The angel eyes from Diode Dynamics are the highest quality and brightness available. Look around, you will not find better angel eyes anywhere for these great prices! Our rings were custom-designed for reliability and long life, and have been tested on your vehicle for perfect fitment. 

These angel eyes have been test-fit on your vehicle for perfect fitment. To read more about Angel Eye Rings, click here.

RGB SMD Design

These are LED rings which use 5050 size SMDs. The SMD LED chips are mounted directly on to the circular board, facing forward. The LEDs go all the way around the ring, for no "break" in the light as with other angel eye designs. This provides an extremely high light output in the forward direction. 

Typically, LED rings have resistors mounted directly on to the ring. Our RGB have improved durability and reliability by using external current regulators. The regulators are housed in a small, fully-potted (waterproof) regulator box, which is simply attached inline between the controller and the LED ring. RGB Multicolor rings have a standard 4-pin RGB connector, compatible with Diode Dynamics RGB controllers. Either controller can be used to control the rings.

What's Included

Kit includes:

  • Four (4) 5050-SMD Rings, fitted for your vehicle
  • Diode Dynamics Plug-and-Play Wiring Harness
  • Red LED Toggle switch
  • 3-year limited replacement warranty
  • 30-day satisfaction guarantee



Installation requires you to open the headlight, by using heat from either your oven or a heat gun. It sounds bad, but really isn't too hard. Simply remove all screws, heat the seal, and pull apart. We have installation videos and other helpful guides available at The wiring is a plug-and-play installation, using our Diode Dynamics Angel Eye Harness and quick disconnects. You will not have to do any soldering, wire stripping, crimping or anything. The rings only need 12V power and ground- we recommend using your parking lights, in order to have them turn on like they came that way from the factory, "OEM style."

Don't want to do it yourself? Looking for a kit for a different model? We can do any vehicle for you, with our large inventory of ring sizes. Contact us for information.

Year 2008,2009,2010,2011,2012,2013,2014
Make Dodge
Model Challenger
Application Angel Eyes
  1. Angel eyes halos Review by Eddie

    Absolutely amazing look to my car for the best price and quality Diode Dynamics is the way to go. (Posted on 8/12/15)

  2. These look great Review by Mike

    I chose diode dynamics per a recommendation from my installer. I love the look of these! The app and light control are great! I highly recommend to give your car a great look (Posted on 2/27/15)

  3. Show Stopper Mod-LED Switch option Review by Rich S

    This is more of an elaboration on previous review as it pertains to the LED Switch option offered by DD.

    I opted for the Blue Led switch for my project. You can go with the method of tapping into the fog lights lower source, but I wanted to be able to have just the Angel Eyes on for specific occasions if I wanted. The switch base color matches the Challenger panel extremely well and the LED is flawless. (Nice work DD!) Cost for the switch is minimal to give yourself the extra option of separating what you want illuminated.
    Now, many want to know how I got the wiring and switch where I did. Fairly easy actually. There is a rubber grommet on the firewall the brings in a bundle of other wires. The grommet is about 3" in diameter and is located to the door side of the steering assembly. I strongly recommend being very careful when poking a hole through the grommet due to the proximity of the bundled wires already present. I unwound an old wire hanger from the closet and slightly sharpened the end (with a grinder), that had the metal winding un-straightened (not the hanger hook end). I carefully poked it through the grommet close to the wire bundle and downward about 30 degrees and fed it on through. It took me a minute or two to find it from inside the cabin, but I did. The reason I fed the un-straightened end through is those ripples make a nice grab point for your DD Switch wires to be taped to. When you pull it to feed the wires through the grommet, it will have less chance of pulling off the coat hanger and having to start over on re-taping.
    Had another car guy tell me that the LED switch and install looked "factory".

    I've included a pic for approval for reference. (Posted on 7/22/14)

  4. Show Stopper Mod! Review by Rich S

    Absolutely love these...and so do judges, family and friends!
    I installed these the weekend before July 4th holiday. Top quality product. The install took just over 24 hours due to drying time of the ring sealant I used. I recommend using a clear RTV sealant to mount the rings and a Black RTV sealant to seal up the housings. I tried the oven method of heating the housings and could not get them, so I broke out the dremel w/ plastic cutting disk. I also spent the time to enclose all the wiring in split tubing so there would be minimal chance of a wire getting chaffed or severed by some of the edges in the nose of the Challenger. DD is outstanding...even hung on the phone with me while I rambled on about how great the angel eye kit was and how bright the rings are.

    I also opted for the blue LED switch and mounted it beside the trunk release switch on the lower left dash panel.

    Get these installed and be prepared to talk to just about anybody who sees them! Showstoppers! (Posted on 7/21/14)

Worry-free warranty

  • -Full 3-year warranty on all products
  • -No waiting: we usually send new items out with a return label (US customers only)


You will get quick help from our trained staff for any issues.

All Stage Series products carry a limited 8-year warranty.

For further details, please see our full article.

Domestic (US) Customers

  • - Same-day shipping for all orders placed by 12:00 PM CST (or until 4 PM with rush processing)
  • - USPS, for delivery in 3-5 days (on average)
  • - Express services are available, see exact pricing at checkout
  • - Fully Insured


International Customers

  • - We ship to all countries via standard mail
  • - Usually around $10 for LEDs, or $25 for HIDs.
  • - Choose your service on checkout to see exact prices:
  • - USPS 1st Class: 2-5 weeks
  • - USPS Priority: 1-2 weeks
  • - Express EMS: 1 week
  • - Please email us if you are unsure about shipping to your country.

You will receive updates from our site when your order is shipped, along with a unique shipment number to ensure that your order is correctly accounted for. This allows you to easily reply to us if you have any concerns.

Whether your order is big or small, it is tested through many run cycles, and each bulb is tested before shipment. Every single bulb. Every time. And if anything does go wrong, you can rely on our industry-leading warranty for worry-free replacement.

If you're not happy with your items, we want to make it right. So we have some pretty awesome return policies:


30 day return policy. All customers have 30 days from the date of original order shipment to return items.

Full refund, no fees. At Diode Dynamics, we offer free returns. That means no restocking fees, no administrative fees, and no hassle!

 Free return label. If your original order was over $50, you get a free return label for your items (US customers only). If your order was less than $50 or international, you can send the items back through your preferred method.


Within 30 days: If your original order was over $50, you can get new items shipped to you with a return label (US customers only). If your order was less than $50 or international, we can send you the new items first, but you are responsible for returning the old items.

Within 90 days: Any item can be returned for exchange or store credit within 90 days. The buyer is responsible for the cost of the return shipping, and must first return the old items. We'll still cover the postage for the new items.


Please note: due to the nature of custom acrylic pieces, we cannot offer any refund or exchange for returned custom acrylic items.


To make a return or exchange, please request an RMA, or give us a call. When we get it back, you will be notified and credited appropriately.

Again, all returns must be approved, with an RMA. This is so that we can process your return as quickly as possible when we get it. If you would like to return an item, please Request an RMA. Please include as much information as possible about the reason for return.

Alternatively, you can also send us a message, or give us a call!