From the factory, rear turn signal bulbs are powered by standard incandescant lights that light up white in color, and cast light through your red or amber tail light lens. This results in a washed-out color.
Newer luxury vehicles are using LEDs for turn signals, because LEDs offer a crisp, instant on/off function, increased brightness, and true, vibrant color. By replacing the bulbs in your vehicle, you can achieve this modern look!
The installation is 100% plug-and-play, just replace your factory bulb. The bulb may blink faster since it uses less power, and your vehicle thinks the bulb is out- to fix this, please see "hyperblinking" section below.
SMD27: 27 three-chip 5050-size Epistar SMDs arranged in 360 degrees. Six radial panels of three chips, and a forward-facing six-chip panel. Main body material is PCB.
HP11: Four side-firing 1.5W-rated Osram LED chips, and one 5W-rated CREE LED chip on top, which is projected by a lens for maximum effective brightness. The bulb is housed in a machined aluminum casing, which provides superior heat diffusion for long life.
XP80: Each of the four sides of this bulb contains three 5W-rated CREE chips, and the top is fitted with four more under a projector lens. This is the brightest self-contained automotive LED bulb on the market, and is housed in an aluminum casing with a textured finish for maximum heatsinking properties.
Fitment. All three bulbs use a quality inject-molded 3157 terminal, with a full-size base connector and proper pin alignment, designed for exact replacement of your factory 3157 bulb.
Included in your order is SIX BULBS.
These LEDs illuminate in a crisp, bright, red hue. Select the color of your rear turn signal lens.
At Diode Dynamics, we rate the brightness of LEDs in "stages" so you can choose what fits you best.
SMD27: Slightly lower brightness than OEM bulbs, but still provides the crisp, modern instant on/off of LED technology.
HP11: Slightly higher brightness than OEM bulbs.
XP80: Much brighter than OEM bulbs. These are bright!
Lumens. 99% of sellers online simply provide "calculated" lumen numbers based on the maximum potential brightness of the bulb. For example, if a bulb has five 10-lumen chips, they will rate it at 50 lumens. However, this is far from accurate, as the design of an LED bulb rarely provides the proper conditions for maximum brightness, once it is all put together. We do not provide calculated numbers, as we believe it is misleading to the consumer. Please reference our pictures for brightness comparison. We do not currently list lumen brightness ratings for our products yet- however, we've just purchased the required equipment, and will be posting accurate measurement numbers soon!
LED Components. Diode Dynamics uses only the highest quality LED chips in the production of its bulbs. This means we use only brand-name suppliers such as Epistar, Cree, Osram, and Samsung.
While our bulbs may look the same as others on the market, most copycat bulbs use economy-grade LED chips in order to reduce costs. This greatly reduces the reliability and overall brightness of the bulb when you compare it to Diode Dynamics.
Construction. Although LED technology allows for extremely long bulb life, the market is flooded with cheap LED bulbs that fail prematurely due to inferior construction. The worst enemy of LEDs is excessive heat, and when bulbs are not designed properly, they do not disperse heat as well, leading to premature failure.
Off-brand, cheap bulbs exhibit poor solder uniformity, high levels of flux in the solder, uneven chip placement, low-gauge terminal wires, poor assembly, and bulbs held together with inferior adhesives. At best, solder joints will crack and fail on low-quality LEDs after a few weeks of use. In the worst case, these bulbs can damage housings as the extra flux and adhesive evaporates and creates a residue on the lens of the housing.
Diode Dynamics bulbs are produced with modern, computerized equipment, and only the best materials, to ensure complete uniformity, high quality, and long bulb life.
The turn signals on most vehicles will begin to blink fast (hyperblink) when LED bulbs are installed. This is because the new LEDs will use less power than the original bulbs, so your vehicle thinks that the bulb is out and warns you by hyperblinking.
This phenomenon will be the same for every LED bulb on the market- there is no such thing as a "no hyperblink" LED bulb, even though some companies advertise them as such.
Resistor Kit: By adding a resistor to the bulb's circuit, you can mimic the power consumption of the original bulb, and return the vehicle to normal turn signal speed. Our resistors are 50W, 6 ohm, and come with extra-long connection wires for easy install. If you have both front and rear LED turn signals, you should purchase one set for each pair, to create enough resistance for the whole turn signal circuit. The installation itself takes only 10-15 minutes, and involves making two simple connections. Everything you need is included in the kit.
Please see the installation video below.
Flasher Replacement: You may have heard of replacing a "flasher relay" instead of using resistors. Indeed, some vehicles have a replaceable flasher relay, and it is possible to replace it with one designed for LED use, to eliminate hyperblinking. However, this is only true for some vehicles. We do not believe one is available for your vehicle, because your flasher is built-in to the vehicle's computer. You will need to use resistors for your vehicle.
|Bulb Size||3157, also known as 3047 3057 3057A 3155 3157A 3357 3454NA 3457A 4057 4157|
|Model||Mustang V6,Mustang California Special,Mustang Ecoboost,Mustang GT,Mustang GT500|
Tail light LEDs are a direct replacement. Just change the bulb! You will not need any resistors or other accessories.
Remove your factory bulb
- 1. Access your tail light bulb. You may need to pull back the trunk/cargo carpet and/or unscrew the visible nuts holding the light in.
- 2. Remove the socket from the tail light by twisting counterclockwise.
- 3. Remove the factory bulb by unclipping and pulling it out of the socket.
Install your new LED bulb
- 1. Plug new LED bulb into socket by pushing it in place.
- 2. Test the bulb to ensure proper function. The bulb should come on half brightness for parking lights, and full brightness for brake. If it does not, try removing the bulb, rotating it, and reinstalling.
- 3. Insert socket back into tail light, and reassemble as necessary. That's it!
- - Full 3-year warranty on all products
- - No waiting: we usually send new items out with a return label (US customers only)
You will get quick help from our trained staff for any issues.
All Off-Road Lighting also carry a limited lifetime warranty.
For further details, please see our full article.
Domestic (US) Customers
- - Just $5 per order with our Diode Delivers program
- - Same-day shipping for all orders placed by 12:00 PM CST (or until 4 PM with rush processing)
- - USPS, for delivery in 2-4 days (on average)
- - Express services are available, see exact pricing at checkout
- - Fully Insured
- - We ship to all countries via standard mail
- - Usually around $10 for LEDs, or $25 for HIDs.
- - Choose your service on checkout to see exact prices:
- - USPS 1st Class: 2-5 weeks
- - USPS Priority: 1-2 weeks
- - Express EMS: 1 week
- - Please email us if you are unsure about shipping to your country.
You will receive updates from our site when your order is shipped, along with a unique shipment number to ensure that your order is correctly accounted for. This allows you to easily reply to us if you have any concerns.
Whether your order is big or small, it is tested through many run cycles, and each bulb is tested before shipment. Every single bulb. Every time. And if anything does go wrong, you can rely on our industry-leading warranty for worry-free replacement.
If you're not happy with your items, we want to make it right. So we have some pretty awesome return policies:
30 day return policy. All customers have 30 days from the date of original order shipment to return items.
Full refund, no fees. At Diode Dynamics, we offer free returns. That means no restocking fees, no administrative fees, and no hassle!
Free return label. If your original order was over $50, you get a free return label for your items (US customers only). If your order was less than $50 or international, you can send the items back through your preferred method.
Within 30 days: If your original order was over $50, you can get new items shipped to you with a return label (US customers only). If your order was less than $50 or international, we can send you the new items first, but you are responsible for returning the old items.
Within 90 days: Any item can be returned for exchange or store credit within 90 days. The buyer is responsible for the cost of the return shipping, and must first return the old items. We'll still cover the postage for the new items.
Please note: due to the nature of custom acrylic pieces, we cannot offer any refund or exchange for returned custom acrylic items.
To make a return or exchange, please request an RMA, or give us a call. When we get it back, you will be notified and credited appropriately.
Again, all returns must be approved, with an RMA. This is so that we can process your return as quickly as possible when we get it. If you would like to return an item, please Request an RMA. Please include as much information as possible about the reason for return.
Alternatively, you can also send us a message, or give us a call!