1156 HP11 is a direct replacement for any 1156-size incandescent bulb. This is one of the brightest bulbs we carry, as a clear improvement over halogen lighting.
The installation is 100% plug-and-play, just replace your factory bulb. The bulb may blink faster since it uses less power, and your vehicle thinks the bulb is out- to fix this, please see "hyperblinking" section below.
This bulb has four 1.5W chips around the sides, to fill in the light's housing and give a great appearance and full look, and one 5W LED chip with a projector lens on top to project outward. It uses an 1156-size durable inject-molded terminal and will fit as a replacement for stock halogen. It uses less power and heat than halogen bulbs, and will last longer, with its engineered aluminum heat-sinking technology. A component is embedded to prevent blowing the LED from voltage surge, and a diode is implanted to protect the LED from reverse polarity. The LED is wired for 12V operation, the kind found on all vehicles.
Included in your order is TWO BULBS.
These LEDs illuminate in a crisp, bright white, amber or red hue. Choose the color of your rear turn signal lens
Lumens: BUYER BEWARE! Most sellers just provide "calculated" lumen numbers, based on the maximum potential brightness of the LED chips on the bulb. For example, if a bulb has five 10-lumen chips, they will rate it at 50 lumens. However, this is not accurate, as the design of an LED bulb does not get rid of heat fast enough to run the LEDs at maximum.
These "calculated" lumen ratings are much, much higher than the true, measured light output, so it will look like competitors' bulbs are brighter than ours. This is because Diode Dynamics does not provide inflated "calculated" numbers; we believe it is misleading. We test the actual brightness of the bulbs in our lab, to provide real lumen output measurements. Our measurements are accurate, but they are usually much lower than the misleading "calculated" figures. Please click here to learn more about LED brightness measurement.
LED Components. Diode Dynamics uses only the highest quality LED chips in the production of its bulbs. This means we use only brand-name suppliers such as Epistar, Cree, Osram, and Samsung.
While our bulbs may look the same as others on the market, most copycat bulbs use economy-grade LED chips in order to reduce costs. This greatly reduces the reliability and overall brightness of the bulb when you compare it to Diode Dynamics.
Construction. Although LED technology allows for extremely long bulb life, the market is flooded with cheap LED bulbs that fail prematurely due to inferior construction. The worst enemy of LEDs is excessive heat, and when bulbs are not designed properly, they do not disperse heat as well, leading to premature failure.
Off-brand, cheap bulbs exhibit poor solder uniformity, high levels of flux in the solder, uneven chip placement, low-gauge terminal wires, poor assembly, and bulbs held together with inferior adhesives. At best, solder joints will crack and fail on low-quality LEDs after a few weeks of use. In the worst case, these bulbs can damage housings as the extra flux and adhesive evaporates and creates a residue on the lens of the housing.
Diode Dynamics bulbs are produced with modern, computerized equipment, and only the best materials, to ensure complete uniformity, high quality, and long bulb life.
The turn signals on most vehicles will begin to blink fast (hyperblink) when LED bulbs are installed. This is because the new LEDs will use less power than the original bulbs, so your vehicle thinks that the bulb is out and warns you by hyperblinking.
This phenomenon will be the same for every LED bulb on the market- there is no such thing as a "no hyperblink" LED bulb, even though some companies advertise them as such.
Flasher Replacement: Replacing the flasher relay, the module that controls blinking speed, is the easiest option to correct hyperblinking. You can remove the flasher on your vehicle, which is a small relay module under the dash, and replace it with a new flasher designed for LEDs. You will only need one flasher for your vehicle, whether you are replacing just one pair or both sets of turn signal bulbs (front/rear).
Resistor Kit: If you prefer not to change the flasher, you can add resistors to the bulb's circuit, and mimic the power consumption of the original bulb, returning the vehicle to normal turn signal speed. Resistors are a universal fix for any vehicle. Our resistors are 50w, 6 ohm, and come with extra-long connection wires for easy install. If you have both front and rear LED turn signals, you should purchase one set for each pair, to create enough resistance for the whole turn signal circuit. The installation itself takes only 10-15 minutes, and involves making two simple connections. Everything you need is included in the kit
|Bulb Size||1156, also known as 1073 1095 1141 1156A 1195 12088 1295 199 2396 3497 631 7506 93 97 97A 97NA|
Excellent! Review by Matt
Price Value Quality
Used a pair of 1156 HP11s in the reverse light fixtures on my 1987 4Runner. Much cleaner, brighter light, and less load (Posted on 12/6/15)
Awesome lights! Review by 2mtech
Quality Price Value
I like these far batter than the OEM incandescents, and really wanted red for the rears. I had the Stage 1's to begin with but am much happier with the brightness of these, especially in bright daylight. (Posted on 4/3/14)
Nice and Bright Review by Bryan
Price Value Quality
These fit great. Bright and red, better than the LED I replaced them with. (Posted on 4/1/13)
These LEDs are super bright Review by DyeSoft
Quality Price Value
I went through about 5 sets of LEDs before this one and none of them could compare in brightness. I haven't compared them yet but I would say that they are at least as bright as the stock bulbs. (Posted on 12/11/12)
Better than OEM's, worth the money spend. Review by Flyin' Dutchman
Quality Price Value
Replaced the OEM 1156A's on my Hyundai Entourage with DD's 1156A 11W LED's, what a difference. This completes the conversion from OEM's to LED's on the Entourage Tail end.
Will order 1157 11W Swithchback LED's, for the Front. (Posted on 11/23/12)
bright rear turn indicators (amber) Review by RR
Quality Price Value
These are bright. the instant on and off is so modern and crisp. Now I can see the instant confirmation of the second click when I unlock the passenger door. (Posted on 11/19/12)
Very bright and amber Review by Adam
Quality Price Value
I love these bulbs! They are just super bright and they match the stock mirror LED amber color turn signals perfectly. This really is a high quality product that produces the brightest amber light that I've ever seen in a LED bulb. I just wish they were cheaper.
I wanted the instant on-off look that only LEDs can give you and I wanted them to be either as bright as or brighter than stock. I ordered cheaper LED bulbs from another site and those looked like a child's nightlight in comparison to the ones that DiodeDynamic offers with their 1156 high powered LED bulbs. it really is a high quality product that produces the brightest amber light that I've ever seen in a LED bulb.
My goal is to completely replace every filament bulb with LEDs as I can't stand the slow responding and cheap looking filament bulbs. (Posted on 9/21/12)
- -Full 3-year warranty on all products
- -No waiting: we usually send new items out with a return label (US customers only)
You will get quick help from our trained staff for any issues.
All Stage Series products carry a limited 8-year warranty.
For further details, please see our full article.
Domestic (US) Customers
- - Just $5 per order with our Diode Delivers program
- - Same-day shipping for all orders placed by 12:00 PM CST (or until 4 PM with rush processing)
- - USPS, for delivery in 2-4 days (on average)
- - Express services are available, see exact pricing at checkout
- - Fully Insured
- - We ship to all countries via standard mail
- - Usually around $10 for LEDs, or $25 for HIDs.
- - Choose your service on checkout to see exact prices:
- - USPS 1st Class: 2-5 weeks
- - USPS Priority: 1-2 weeks
- - Express EMS: 1 week
- - Please email us if you are unsure about shipping to your country.
You will receive updates from our site when your order is shipped, along with a unique shipment number to ensure that your order is correctly accounted for. This allows you to easily reply to us if you have any concerns.
Whether your order is big or small, it is tested through many run cycles, and each bulb is tested before shipment. Every single bulb. Every time. And if anything does go wrong, you can rely on our industry-leading warranty for worry-free replacement.
If you're not happy with your items, we want to make it right. So we have some pretty awesome return policies:
30 day return policy. All customers have 30 days from the date of original order shipment to return items.
Full refund, no fees. At Diode Dynamics, we offer free returns. That means no restocking fees, no administrative fees, and no hassle!
Free return label. If your original order was over $50, you get a free return label for your items (US customers only). If your order was less than $50 or international, you can send the items back through your preferred method.
Within 30 days: If your original order was over $50, you can get new items shipped to you with a return label (US customers only). If your order was less than $50 or international, we can send you the new items first, but you are responsible for returning the old items.
Within 90 days: Any item can be returned for exchange or store credit within 90 days. The buyer is responsible for the cost of the return shipping, and must first return the old items. We'll still cover the postage for the new items.
Please note: due to the nature of custom acrylic pieces, we cannot offer any refund or exchange for returned custom acrylic items.
To make a return or exchange, please request an RMA, or give us a call. When we get it back, you will be notified and credited appropriately.
Again, all returns must be approved, with an RMA. This is so that we can process your return as quickly as possible when we get it. If you would like to return an item, please Request an RMA. Please include as much information as possible about the reason for return.
Alternatively, you can also send us a message, or give us a call!