How to Install: 2024-2026 Toyota Tacoma & 2025-2026 Toyota 4Runner LED Headlights
How to Install: 2024-2026 Toyota Tacoma & 2025-2026 Toyota 4Runner LED Headlights

How to Install: 2024-2026 Toyota Tacoma & 2025-2026 Toyota 4Runner LED Headlights

Form Lighting's Sequential LED Projector Headlights are the perfect upgrade for the 2024-2026 Toyota Tacoma and 2025-2026 Toyota 4Runner. These premium blacked-out headlights feature triple LED projectors, selectable white or amber DRLs, a configurable startup sequence and sequential turn signal, and retained factory leveling.

Both vehicles share the same headlight and the same installation process. The following guide will walk you through installing Form Lighting's LED headlights on the 2024-2026 Toyota Tacoma and 2025-2026 Toyota 4Runner, including connecting the included power harness on gas and hybrid models.

 

Installation Tools

  • 10mm Socket
  • 12mm Socket
  • Ratchet and Extension
  • Pry Tool
  • Long Phillips Head Screwdriver
  • Tape Measure

Estimated Installation Time: 60 minutes

Installation Instructions

Step 1 - Remove Top Cover and Air Plenum

Begin by opening the hood. Use a pry tool to remove the 12 push pins (circled in red), then remove the top radiator cover and air plenum.

Push pins on top radiator cover

Step 2 - Remove Upper Bolts

Use a 10mm socket to remove the three bolts (circled in red) along the top of the bumper.

10mm bolts along top of bumper

Step 3 - Disconnect Headlight Connectors

Disconnect the factory connectors (circled in blue) near the driver and passenger side headlights.

Factory connectors near headlights

Step 4 - Release Fender Liners

Use a 10mm socket to remove the three screws, and a pry tool to unhook the two clips, in each fender liner (circled in red).

Tip: You don't need to undo the twist lock clip. Simply use a pry tool to push it off.

Fender liner screws and clips

Step 5 - Remove Wheel Well Screws

Use a 10mm socket to remove the two screws (circled in red) under the bumper in front of the wheel well. Repeat on the other side.

Screws under bumper in front of wheel well

Step 6 - Remove Lower Bumper Screws

Use a 10mm socket to remove the four screws (circled in red) from the underside of the bumper.

Screws on underside of bumper

Step 7 - Peel Back Fender Flares

Carefully peel back the front edge of the fender flare to access the screw behind it.

Peeling back fender flare

Step 8 - Remove Fender Flare Screw

Use a 10mm socket to remove the screw (circled in red) from behind the fender flare. Repeat on the other side.

Screw behind fender flare

Step 9 - Release Bumper Corners

Pull the corner of the bumper away from the body to release it. Repeat on the other side.

Releasing bumper corner from body

Step 10 - Remove Front Bumper

Remove the front bumper assembly by pulling it straight away from the vehicle.

Removing front bumper assembly

Step 11 - Remove Headlight Screws

Use a 10mm socket to remove the four screws (circled in red) securing the factory headlight. Repeat on the other side.

Headlight mounting screws

Step 12 - Remove Factory Headlights

Pull the headlight forward, away from the vehicle, and disconnect the three factory connectors (circled in blue) from the back of the headlight. Repeat on the other side.

Removing factory headlight and disconnecting connectors

Step 13 - Route FL2048 Power Harness

Route the included FL2048 power harness from the power source to either headlight pocket, keeping it away from any hot or moving parts. Use a 12mm socket to attach the harness terminals to power and ground on the battery.

FL2048 power harness routing

Hybrid models: Use the following steps to connect the power harness at the passenger side fuse box.

Open the passenger side fuse box and use a 12mm socket to remove the nut on the power lug that feeds the hybrid inverter assembly (circled in red).

Hybrid inverter power lug in fuse box

Depress the clip to release the cable lug along with its protective housing.

Releasing cable lug and protective housing

Pry apart and separate the hood of the protective cover from its base.

Separating protective cover hood from base

Remove the bottom base from the power cable.

Removing base from power cable

Reinstall the power cable on the lug along with the FL2048 power harness terminal.

Power cable and harness terminal reinstalled on lug

Reinstall the top protective cover onto the fuse box. The bottom base piece can be discarded.

Protective cover reinstalled

Attach the ground wire from the FL2048 power harness to the hybrid inverter itself or to any chassis ground.

Ground wire attachment point

Step 14 - Configure Form LED Headlights

Before installing, rotate the dust cover on the back of each Form LED Headlight to expose the DIP switches. Set the switches to your desired functions, then reinstall the dust cover.

Switch Function Default Setting Alternate Setting
1 Startup Sequence Welcome Animation Off
2 Turn Signal Sequential Turn Static Turn
3 DRL Color White DRL Amber DRL

DIP switches behind headlight dust cover

Step 15 - Install Form LED Headlights

Connect the three factory connectors and the FL2048 power harness to the Form LED Headlight, then install it using the screws removed in Step 11. Repeat on the other side.

Installing Form LED Headlight

Step 16 - Test Function

Test the headlights to ensure they turn on and every function works.

Important: Do NOT start the engine with the front bumper assembly removed. This can cause a check engine light.

Testing Form LED Headlights

Step 17 - Reinstall Front Bumper

Reinstall the front bumper assembly by reversing Steps 1-10.

Form LED Headlights installed

Step 18 - Set Headlight Leveling Dial

To aim the headlights, park on level ground 25 feet from a wall, facing it straight on. Set the low beam leveling dial to its default position of "0."

Note: Premium trim 4Runners use a different leveling motor with reversed polarity. On these vehicles, the default position is "5" (shown on the right).

Headlight leveling dial default positions

Step 19 - Measure Headlight Height

Use a tape measure to find the distance from the ground to the adjustment dot engraved on the outer lens.

Measuring height to the lens adjustment dot

Step 20 - Aim LED Headlights

On the wall, place marks 0-2" lower than the height measured in the previous step. Then use a long Phillips screwdriver to adjust the beam level to those marks.

For a more detailed description, refer to our headlight aiming guide - How To: Aim Your Headlights.

This completes the installation.

Adjusting headlight aim


Questions About the Installation?

If you have any questions or issues installing Form Lighting's LED Headlights on the 2024-2026 Toyota Tacoma and 2025-2026 Toyota 4Runner, please contact us for further assistance.

Where Can I Buy Form Lighting LED Headlights for the 2024-2026 Toyota Tacoma and 2025-2026 Toyota 4Runner?

If you're ready to upgrade your Tacoma or 4Runner with Form Lighting LED Headlights, you can purchase them for the 2024-2026 Toyota Tacoma or the 2025-2026 Toyota 4Runner, or use our dealer locator to find a dealer near you.

Want to know more about Form Lighting products? Visit diodedynamics.com and subscribe to our newsletter for new product releases and more!

 

This Installation Guide is for the following SKU: FL0107.

Products in the article

Mentioned Products