LED Turn Signal Flasher for 2013-2016 Subaru BRZ

You could receive 20 Diode Points for writing a review for this product.

Availability: In stock

Ships today if ordered in the next 11 hours and 46 minutes!

LED Turn Signal Flasher
Add to Wishlist

LED Turn Signal Flasher for 2013-2016 Subaru BRZ

More Views

Earn $1.00 store credit! Upload a picture of this product installed for 20 Diode Points. (2MB limit)

This is a replacement turn signal flasher module. It will eliminate fast turn signal blinking, known as hyperblinking, that occurs when you replace your turn signal bulbs with LEDs. It has been designed specifically for use with LEDs.

This module is specifically for your vehicle! It will be 100% plug and play. Just remove the factory flasher, and plug this one in.

SmartTap™ Flasher Relay

The SmartTap™ is a replacement turn signal flasher module that adds adjustable one-touch signaling and programmable hazard modes. Programming each mode is simple with the help of the included programming guide and the use of existing vehicle controls.

Tap-to-Signal: One-touch signaling is a convenient way to signal to other drivers when switching lanes. Simply tap the turn signal for a series of signal blinks.

Arrival and Departure Modes: When the lock or unlock button is pressed, the surrounding area will illuminate for better visibility when approaching or leaving the vehicle at night. The lighting time can be adjusted from 10-90 seconds for additional illumination, or disabled if desired.

Unique Hazard Functions: The SmartTap™ has built-in strobe, slo-mo and wig-wag hazard functions to help the vehicle stand out when the hazards are on. Apply these functions on their own, or together for a total of EIGHT unique hazard functions!

The SmartTap™  was designed and fully manufactured by Diode Dynamics, in St. Louis, Missouri. It is fully made in USA.


Why do you need this module? When your factory turn signal bulbs go out, your vehicle's flasher senses that less power is being used, and it will blink the turn signals quickly to alert you. When LED turn signal bulbs are installed, it lowers the load on the circuit too, because LEDs use less power. You get the fast blinking, known as "hyperblinking," even though the LEDs are functioning just fine. Basically, your car thinks the bulbs went out!

To slow down the blinking to regular speed, you can add resistors to increase the circuit's power consumption again. However, whenever possible, replacing the flasher with a module like this is the easiest option. This is the unit that actually controls the blinking speed, and makes the "clicking" noise.

Bulb Size No
Year 2013,2014,2015,2016
Make Subaru
Model BRZ
Application LED Flashers
  1. Can't beat this Review by Will

    Quick and cheap fix for hyper flash. Worth ever penny (Posted on 5/6/17)

  2. Fixes hyperflash but adds more issues Review by Omi

    - Fixed hyperflash
    - First signal/click is delayed then then normal rate clicking
    - Clock and passenger side "airbag is off" light will click along with turn signal.
    - Opposite side of tail lights will randomly click when the signal is on at the opposite side. So when I turn on right signal, the left tail light will click as well (and it's the actual taillight that clicks not the signal part). This happens sporadically.

    DD has offered to send me replacement flasher i will test it out and update my review. (Posted on 10/12/16)

  3. Fixes hyperblinking, introduces long first blink Review by Jim

    Similar review as Isolato ... The unit is well built and does what it says it will do - the hyperblinking is gone.

    However - the first flash of the signals after you hit the signal is noticeably longer than stock. Takes a bit of getting used to...

    Minor annoyance on an otherwise solid product. (Posted on 8/19/16)

  4. Works good. Could be better. Review by Isolato

    First things first. This flasher relay does what it is supposed to do: it fixes hyperblinking associated with LED flasher bulbs, and it works with any combination of incandescent and LED bulbs. The unit is solidly built, and is offered at a very competitive price.

    Here are my nit-pics, that I'd love to see Diode Dynamics address. The relay clicking is louder than stock, and the first "blink" of the blinking sequence is much longer than the rest. To each his own, but I personally find both of these aspects annoying.

    Lastly, I'd love it if Diode Dynamics offered a "tap turn" relay that allowed the driver to flash 3-blinks automatically by just tapping the turn signal (as offered on most cars these days). (Posted on 8/14/16)

  5. Needed of course! Review by Samson

    Better than a resistor! Not hard to install although it was hard for me to find the port. (Posted on 2/15/16)

  6. Easy hyperblink fix Review by William

    Easy to install and installs in under a minute. It works with LED and stock bulbs. Doesn't matter what turn signals you use it will always blink at the same rate. (Posted on 7/7/15)

  7. You need it. It works. Get it. Review by Zaneman

    This thing works and installs in under a minute. End of story. Wait there is more..It works with LED and stock bulbs. I had it installed with rear LED bulbs and stock fronts and there was no issue. If you want the look of beautiful LED blinkers then you need this. (Posted on 12/16/14)

  8. It Works Review by Nick

    Easy to install, and its works. hides under the dash nicely! Highly recommended. (Posted on 11/26/14)

  9. Better than resistors Review by Alex C.

    Bought these to go along with the LED front turn signals. Definitely get these rather than tinker with the wiring and resistors. It took me some time to pull the stock flasher out under the steering column but it wasn't too bad. There is a noticeable initial delay if you look closely but I didn't mind it as there is no more hyper blinking! (Posted on 9/13/14)

  10. Essential Buy IMO Review by MikeBRZ

    I watched many YouTube videos on soldering resistors and such into the wiring when upgrading to LED turn signals in the BRZ. I was really hesitant to do that because I have no expertise in that kind of handiwork. Then I found this, and it was the most valuable purchase for me when it came to upgrading my turn signals. Easy installation, but it helps if you have someone nearby with really small hands to install it. Love this flasher because it prevents me from potentially screwing up the exterior lighting in my car! Definitely would recommend this product. (Posted on 6/16/14)

  11. Fixes hyperflash and no initial signal delay Review by Los

    Bought this when the flasher that came with my new tail lights had an initial delay when signaling. DD's works how it should. (Posted on 5/30/14)

  12. Easy hyper flash fix Review by Tristaneasy firtu stab

    Got this along with my switchback led turn signals for my FRS. Works perfectly. Blinks at stock rate. Doesn't matter what turn signals you use. Oem or led it will always blink at the same rate because it's digitally limited. Super easy install. (Posted on 5/29/14)

Worry-free warranty

  • -Full 3-year warranty on all products
  • -No waiting: we usually send new items out with a return label (US customers only)


You will get quick help from our trained staff for any issues.

All Stage Series products carry a limited 8-year warranty.

For further details, please see our full article.

Domestic (US) Customers

  • - Same-day shipping for all orders placed by 12:00 PM CST (or until 4 PM with rush processing)
  • - USPS, for delivery in 3-5 days (on average)
  • - Express services are available, see exact pricing at checkout
  • - Fully Insured


International Customers

  • - We ship to all countries via standard mail
  • - Usually around $10 for LEDs, or $25 for HIDs.
  • - Choose your service on checkout to see exact prices:
  • - USPS 1st Class: 2-5 weeks
  • - USPS Priority: 1-2 weeks
  • - Express EMS: 1 week
  • - Please email us if you are unsure about shipping to your country.

You will receive updates from our site when your order is shipped, along with a unique shipment number to ensure that your order is correctly accounted for. This allows you to easily reply to us if you have any concerns.

Whether your order is big or small, it is tested through many run cycles, and each bulb is tested before shipment. Every single bulb. Every time. And if anything does go wrong, you can rely on our industry-leading warranty for worry-free replacement.

If you're not happy with your items, we want to make it right. So we have some pretty awesome return policies:


30 day return policy. All customers have 30 days from the date of original order shipment to return items.

Full refund, no fees. At Diode Dynamics, we offer free returns. That means no restocking fees, no administrative fees, and no hassle!

 Free return label. If your original order was over $50, you get a free return label for your items (US customers only). If your order was less than $50 or international, you can send the items back through your preferred method.


Within 30 days: If your original order was over $50, you can get new items shipped to you with a return label (US customers only). If your order was less than $50 or international, we can send you the new items first, but you are responsible for returning the old items.

Within 90 days: Any item can be returned for exchange or store credit within 90 days. The buyer is responsible for the cost of the return shipping, and must first return the old items. We'll still cover the postage for the new items.


Please note: due to the nature of custom acrylic pieces, we cannot offer any refund or exchange for returned custom acrylic items.


To make a return or exchange, please request an RMA, or give us a call. When we get it back, you will be notified and credited appropriately.

Again, all returns must be approved, with an RMA. This is so that we can process your return as quickly as possible when we get it. If you would like to return an item, please Request an RMA. Please include as much information as possible about the reason for return.

Alternatively, you can also send us a message, or give us a call!