Rear Turn Signal LEDs for 2013-2016 Hyundai Genesis Coupe (pair)

You could receive 20 Diode Points for writing a review for this product.

Availability: In stock

Ships tomorrow if ordered in the next 15 hours and 12 minutes!

Upgrade to LED!
  • Red
  • Amber
  • HP48 (280 lumens)
  • HP11 (310 lumens)
  • XP80 (520 lumens)

A set of 6 ohm resistors and connectors, to slow down the fast-blinking caused by LEDs. Can be used on any vehicle. See install video and information below.

Add to Wishlist

Rear Turn Signal LEDs for 2013-2016 Hyundai Genesis Coupe (pair)

More Views

  • HP11
  • XP80
Customer Images
Earn $1.00 store credit! Upload a picture of this product installed for 20 Diode Points. (2MB limit)


From the factory, rear turn signal bulbs are powered by standard incandescent lights that light up white in color, and cast light through your red or amber tail light lens. This results in a washed-out color.

Newer luxury vehicles are using LEDs for turn signals, because LEDs offer a crisp, instant on/off function, increased brightness, and true, vibrant color. By replacing the bulbs in your vehicle, you can achieve this modern look!

The installation is 100% plug-and-play, just replace your factory bulb. The bulb may blink faster since it uses less power, and your vehicle thinks the bulb is out- to fix this, please see "hyperblinking" section below.



HP48: This bulb is non-polar, CK compatible, with 48 Epistar 3014 LED chips. Thanks to the cap on the top, the light from this High Power Bulb is shined backwards and away from the bulb, not straight out. This means the output is excellent, because it uses the vehicle's housing completely, which then shines the light much more uniformly.

HP11: Four side-firing 1.5W-rated Osram LED chips, and one 5W-rated LED chip on top, which is projected by a lens for maximum effective brightness. The bulb is housed in a machined aluminum casing, which provides superior heat diffusion for long life.

XP80: Each of the four sides of this bulb contains three 5W-rated chips, and the top is fitted with four more under a projector lens. This is the brightest self-contained automotive LED bulb on the market, and is housed in an aluminum casing with a textured finish for maximum heatsinking properties.

Fitment. All three bulbs use a quality aluminum 1156 terminal, with a full-size base connector and proper pin alignment, designed for exact replacement of your factory 1156 bulb.

Included in your order is TWO BULBS.


These LEDs illuminate in a crisp, bright, amber or red hue. Select the color of your rear turn signal lens.


Diode Dynamics offers several brightness options so you can choose what fits you best.  These options are listed by the design and the lumen output of each bulb: 

HP48: Slightly lower brightness than OEM bulbs, but still provides the crisp, modern instant on/off of LED technology.
HP11: Slightly higher brightness than OEM bulbs.
XP80: Much brighter than OEM bulbs. These are bright!

Lumens: BUYER BEWARE! Most sellers just provide "calculated" lumen numbers, based on the maximum potential brightness of the LED chips on the bulb. For example, if a bulb has five 10-lumen chips, they will rate it at 50 lumens. However, this is not accurate, as the design of an LED bulb does not get rid of heat fast enough to run the LEDs at maximum.

These "calculated" lumen ratings are much, much higher than the true, measured light output, so it will look like competitors' bulbs are brighter than ours. This is because Diode Dynamics does not provide inflated "calculated" numbers; we believe it is misleading. We test the actual brightness of the bulbs in our lab, to provide real lumen output measurements. Our measurements are accurate, but they are usually much lower than the misleading "calculated" figures. Please click here to learn more about LED brightness measurement.



LED Components. Diode Dynamics uses only the highest quality LED chips in the production of its bulbs. This means we use only brand-name suppliers such as Epistar, Cree, Osram, and Samsung.

While Diode Dynamics bulbs may look the same as others on the market, most copycat bulbs use economy-grade LED chips in order to reduce costs. This greatly reduces the reliability and overall brightness of the bulb when you compare it to Diode Dynamics.

Construction. Although LED technology allows for extremely long bulb life, the market is flooded with cheap LED bulbs that fail prematurely due to inferior construction. The worst enemy of LEDs is excessive heat, and when bulbs are not designed properly, they do not disperse heat as well, leading to premature failure.

Off-brand, cheap bulbs exhibit poor solder uniformity, high levels of flux in the solder, uneven chip placement, low-gauge terminal wires, poor assembly, and bulbs held together with inferior adhesives. At best, solder joints will crack and fail on low-quality LEDs after a few weeks of use. In the worst case, these bulbs can damage housings as the extra flux and adhesive evaporates and creates a residue on the lens of the housing.

Diode Dynamics bulbs are produced with modern, computerized equipment, and only the best materials, to ensure complete uniformity, high quality, and long bulb life.

All Diode Dynamics products come with a 30-day satisfaction guarantee and a 3-year limited replacement warranty. For more information, please view the Warranty Information page.


The turn signals on most vehicles will begin to blink fast (hyperblink) when LED bulbs are installed. This is because the new LEDs will use less power than the original bulbs, so your vehicle thinks that the bulb is out and warns you by hyperblinking.

This phenomenon will be the same for every LED bulb on the market- there is no such thing as a "no hyperblink" LED bulb, even though some companies advertise them as such.

Resistor Kit: By adding a resistor to the bulb's circuit, you can mimic the power consumption of the original bulb, and return the vehicle to normal turn signal speed. Diode Dynamics resistors are 50W, 6 ohm, and come with extra-long connection wires for easy install. If you have both front and rear LED turn signals, you should purchase one set for each pair, to create enough resistance for the whole turn signal circuit. The installation itself takes only 10-15 minutes, and involves making two simple connections. Everything you need is included in the kit. 
Please see the installation video below.

Flasher Replacement: You may have heard of replacing a "flasher relay" instead of using resistors. Indeed, some vehicles have a replaceable flasher relay, and it is possible to replace it with one designed for LED use, to eliminate hyperblinking. However, this is only true for some vehicles. We do not believe one is available for your vehicle, because your flasher is built-in to the vehicle's computer. You will need to use resistors for your vehicle.


Bulb Size 1156, also known as 1073 1095 1141 1156A 1195 12088 1295 199 2396 3497 631 7506 93 97 97A 97NA
Year 2013,2014,2015,2016
Make Hyundai
Model Genesis Coupe
Application LED Bulbs
  1. Super bright Review by Francesco

    I went with the stage 2 amber set and these LED's look awesome! Super easy to install. I did remove the tail light to install these so that it was easier to install the resistors to counter the hyper blink. Install took less than 15 min including install of the resistors. Diode Dynamics makes great YouTube videos that help with all the instillations! (Posted on 2/9/16)

  2. Easy replacement, perfect fitting Review by Steve

    Took all of 5 minutes to install. The LEDs deliver the crisp on/off effect and are definitely brighter than OEMs (Posted on 4/22/15)

  3. not very bright Review by Charles

    I ordered the 205 lumen $30 bulbs. The build quality is good BUT they are significantly less bright than the factory bulbs. I am going to order the 510 lumen bulbs because DD does build quality products and the ones I ordered are advertised as not being as bright as oem. (Posted on 2/16/15)

  4. Bit pricey but awesome results! Review by jsmedina3

    Got XP80 for my 14' Gen Coupe in red to match the LED stop lights and they look so much better and they are BRIGHT!! (Posted on 1/13/15)

  5. Really Great Mod Review by Bryan

    Just added these to my recently purchased 2014 Genesis. HUGE difference from the stock bulbs. The bright red really gives it a nice touch! (Posted on 7/30/14)

  6. Excellent Review by Sim

    I bought the Amber Stage III + Resistor kit for my 2013 Genesis Coupe 2.0 R-spec. They function really well and look really cool.
    Initially, I was getting hyperblinking despite the resistors, but I contacted Diode Dynamics support and they effectively helped me wire it right (thanks DD!) - I had tapped the incorrect wires into the resistors. To fix hyperblinking, you need to make the correct color-resistor connections.
    Note: A flasher will not work for the 2013 models. You will need the resistor kit. (Posted on 6/2/14)

  7. Perfect match! Review by Robert

    I got the Red Stage 2 turn signals for the rear so they would match my factory LED Taillights and they blend perfectly. When the blinker lights up, the whole taillight is a solid red and looks beautiful. The hyperblink kit is a must for the Gen Coupe, and was easy to install, once you get around the very short segment of wire the stock taillight housing has. (Posted on 3/18/14)

  8. A very nice upgrade to the 2013 design Review by Obiwan

    These bulbs were installed on a 2010 3.8 Genesis Coupe that has the EP34 module installed. Stage 1 red LED's were selected to complement the tail and brake lights. They look great and are just the right brightness. A great pairing to the LED backup bulbs! (Posted on 10/6/13)

  9. perfect match Review by donald

    these were perfect match on my 2013 i bought there bright ones in red and they are sweet (Posted on 9/25/13)

  10. Great Product!!!! Review by Fireman305

    I have a 2013 Genesis Coupe 3.8 Track and I love these LED turn signals, they definitely make my car stand out more and they look awesome! Great price and shipping was fast and cheap! If you have the same car as I do then your going to need the resistors for the LED's or else you get hyper blink. Very easy to install as well. (Posted on 8/6/13)

  11. Good quality bulbs Review by Michael

    Purchased a set of amber stage 2 bulbs for my 2013 Gen Coupe. Install was simple and quick. The light output of these LEDs are much brighter than the original stock amber bulbs, and it also complements my stock red rear LEDs nicely. The quality of the bulb is very good and can be felt in the heftyness of its weight. (Posted on 5/26/13)

Worry-free warranty

  • -Full 3-year warranty on all products
  • -No waiting: we usually send new items out with a return label (US customers only)


You will get quick help from our trained staff for any issues.

All Stage Series products carry a limited 8-year warranty.

For further details, please see our full article.

Domestic (US) Customers

  • - Same-day shipping for all orders placed by 12:00 PM CST (or until 4 PM with rush processing)
  • - USPS, for delivery in 3-5 days (on average)
  • - Express services are available, see exact pricing at checkout
  • - Fully Insured


International Customers

  • - We ship to all countries via standard mail
  • - Usually around $10 for LEDs, or $25 for HIDs.
  • - Choose your service on checkout to see exact prices:
  • - USPS 1st Class: 2-5 weeks
  • - USPS Priority: 1-2 weeks
  • - Express EMS: 1 week
  • - Please email us if you are unsure about shipping to your country.

You will receive updates from our site when your order is shipped, along with a unique shipment number to ensure that your order is correctly accounted for. This allows you to easily reply to us if you have any concerns.

Whether your order is big or small, it is tested through many run cycles, and each bulb is tested before shipment. Every single bulb. Every time. And if anything does go wrong, you can rely on our industry-leading warranty for worry-free replacement.

If you're not happy with your items, we want to make it right. So we have some pretty awesome return policies:


30 day return policy. All customers have 30 days from the date of original order shipment to return items.

Full refund, no fees. At Diode Dynamics, we offer free returns. That means no restocking fees, no administrative fees, and no hassle!

 Free return label. If your original order was over $50, you get a free return label for your items (US customers only). If your order was less than $50 or international, you can send the items back through your preferred method.


Within 30 days: If your original order was over $50, you can get new items shipped to you with a return label (US customers only). If your order was less than $50 or international, we can send you the new items first, but you are responsible for returning the old items.

Within 90 days: Any item can be returned for exchange or store credit within 90 days. The buyer is responsible for the cost of the return shipping, and must first return the old items. We'll still cover the postage for the new items.


Please note: due to the nature of custom acrylic pieces, we cannot offer any refund or exchange for returned custom acrylic items.


To make a return or exchange, please request an RMA, or give us a call. When we get it back, you will be notified and credited appropriately.

Again, all returns must be approved, with an RMA. This is so that we can process your return as quickly as possible when we get it. If you would like to return an item, please Request an RMA. Please include as much information as possible about the reason for return.

Alternatively, you can also send us a message, or give us a call!